Empathy List Archives

RM

Raghu Meesala

Thu, Jan 14, 2016 2:53 PM

Hello:

I am using ANSYS with LS-DYNA.

Problem: I am trying to understand the forces applied on a solid ball (3.56" diameter) which is sheared through a hollow pipe (3.5" inch ID)
Question: 1. How to import the ball into ANSYS so that I can place the ball at the starting point of the pipe and apply pressure. When I try to import the IGES I get it aligned to the center and I am unable to place where I would like to.

How can I select only the areas which I want to mesh, I want to select only the pipe areas after meshing to constraint the boundary conditions.

Any literature or links for ANSYS LS-DYNA will be helpful. Thanks.

Raghu Meesala
Terves Inc.

Hello: I am using ANSYS with LS-DYNA. Problem: I am trying to understand the forces applied on a solid ball (3.56" diameter) which is sheared through a hollow pipe (3.5" inch ID) Question: 1. How to import the ball into ANSYS so that I can place the ball at the starting point of the pipe and apply pressure. When I try to import the IGES I get it aligned to the center and I am unable to place where I would like to. 2. How can I select only the areas which I want to mesh, I want to select only the pipe areas after meshing to constraint the boundary conditions. Any literature or links for ANSYS LS-DYNA will be helpful. Thanks. Raghu Meesala Terves Inc.

DS

Dinesh Sharma-Mech

Fri, Jan 15, 2016 3:18 AM

you can do these tasks in repost, which is free on latch website.
regards
Dinesh Sharma
Analyst
secure meters limited

From: Xansys-temp [xansys-temp-bounces@xansystest.info] on behalf of Raghu Meesala [rmeesala@tervesinc.com]
Sent: 14 January 2016 21:23
To: XANSYS Mailing List Temporary Home
Subject: [Xansys] Help with LS-DYNA (Contact/Shear Problem)

Hello:

I am using ANSYS with LS-DYNA.

Problem: I am trying to understand the forces applied on a solid ball (3.56" diameter) which is sheared through a hollow pipe (3.5" inch ID)
Question: 1. How to import the ball into ANSYS so that I can place the ball at the starting point of the pipe and apply pressure. When I try to import the IGES I get it aligned to the center and I am unable to place where I would like to.

How can I select only the areas which I want to mesh, I want to select only the pipe areas after meshing to constraint the boundary conditions.

Any literature or links for ANSYS LS-DYNA will be helpful. Thanks.

Raghu Meesala
Terves Inc.

Xansys-temp mailing list
Xansys-temp@xansystest.info
http://xansystest.info/mailman/listinfo/xansys-temp_xansystest.info
If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode.

Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list
This e-mail and any files transmitted with it are for the sole use of the intended recipient(s) and may contain confidential and privileged information. If you are not the intended recipient, please contact the sender and destroy all copies and the original message. Secure Meters Limited or its subsidiaries (Secure), are unable to exercise control or guarantee the integrity of/over the content contained in e-mails and any views expressed in this message are those of the individual unless expressly stated with due authority of Secure. If you have any problems with the emails from Secure contact: netadmin@securetogether.com

you can do these tasks in repost, which is free on latch website. regards Dinesh Sharma Analyst secure meters limited ________________________________________ From: Xansys-temp [xansys-temp-bounces@xansystest.info] on behalf of Raghu Meesala [rmeesala@tervesinc.com] Sent: 14 January 2016 21:23 To: XANSYS Mailing List Temporary Home Subject: [Xansys] Help with LS-DYNA (Contact/Shear Problem) Hello: I am using ANSYS with LS-DYNA. Problem: I am trying to understand the forces applied on a solid ball (3.56" diameter) which is sheared through a hollow pipe (3.5" inch ID) Question: 1. How to import the ball into ANSYS so that I can place the ball at the starting point of the pipe and apply pressure. When I try to import the IGES I get it aligned to the center and I am unable to place where I would like to. 2. How can I select only the areas which I want to mesh, I want to select only the pipe areas after meshing to constraint the boundary conditions. Any literature or links for ANSYS LS-DYNA will be helpful. Thanks. Raghu Meesala Terves Inc. _______________________________________________ Xansys-temp mailing list Xansys-temp@xansystest.info http://xansystest.info/mailman/listinfo/xansys-temp_xansystest.info If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode. Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list This e-mail and any files transmitted with it are for the sole use of the intended recipient(s) and may contain confidential and privileged information. If you are not the intended recipient, please contact the sender and destroy all copies and the original message. Secure Meters Limited or its subsidiaries (Secure), are unable to exercise control or guarantee the integrity of/over the content contained in e-mails and any views expressed in this message are those of the individual unless expressly stated with due authority of Secure. If you have any problems with the emails from Secure contact: netadmin@securetogether.com

RM

Raghu Meesala

Fri, Jan 15, 2016 2:51 PM

Hey Dinesh:
I tried searching for latch but have not been lucky. Thank you for the thought.

Any other solutions please ?

Regards
Raghu Meesala
Terves Inc.

-----Original Message-----
From: Xansys-temp [mailto:xansys-temp-bounces@xansystest.info] On Behalf Of Dinesh Sharma-Mech
Sent: Thursday, January 14, 2016 10:19 PM
To: XANSYS Mailing List Temporary Home xansys-temp@xansystest.info
Subject: Re: [Xansys] Help with LS-DYNA (Contact/Shear Problem)

you can do these tasks in repost, which is free on latch website.
regards
Dinesh Sharma
Analyst
secure meters limited

From: Xansys-temp [xansys-temp-bounces@xansystest.info] on behalf of Raghu Meesala [rmeesala@tervesinc.com]
Sent: 14 January 2016 21:23
To: XANSYS Mailing List Temporary Home
Subject: [Xansys] Help with LS-DYNA (Contact/Shear Problem)

Hello:

I am using ANSYS with LS-DYNA.

Problem: I am trying to understand the forces applied on a solid ball (3.56" diameter) which is sheared through a hollow pipe (3.5" inch ID)
Question: 1. How to import the ball into ANSYS so that I can place the ball at the starting point of the pipe and apply pressure. When I try to import the IGES I get it aligned to the center and I am unable to place where I would like to.

How can I select only the areas which I want to mesh, I want to select only the pipe areas after meshing to constraint the boundary conditions.

Any literature or links for ANSYS LS-DYNA will be helpful. Thanks.

Raghu Meesala
Terves Inc.

Xansys-temp mailing list
Xansys-temp@xansystest.info
http://xansystest.info/mailman/listinfo/xansys-temp_xansystest.info
If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode.

Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list This e-mail and any files transmitted with it are for the sole use of the intended recipient(s) and may contain confidential and privileged information. If you are not the intended recipient, please contact the sender and destroy all copies and the original message. Secure Meters Limited or its subsidiaries (Secure), are unable to exercise control or guarantee the integrity of/over the content contained in e-mails and any views expressed in this message are those of the individual unless expressly stated with due authority of Secure. If you have any problems with the emails from Secure contact: netadmin@securetogether.com

Xansys-temp mailing list
Xansys-temp@xansystest.info
http://xansystest.info/mailman/listinfo/xansys-temp_xansystest.info
If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode.

Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list

Hey Dinesh: I tried searching for latch but have not been lucky. Thank you for the thought. Any other solutions please ? Regards Raghu Meesala Terves Inc. -----Original Message----- From: Xansys-temp [mailto:xansys-temp-bounces@xansystest.info] On Behalf Of Dinesh Sharma-Mech Sent: Thursday, January 14, 2016 10:19 PM To: XANSYS Mailing List Temporary Home <xansys-temp@xansystest.info> Subject: Re: [Xansys] Help with LS-DYNA (Contact/Shear Problem) you can do these tasks in repost, which is free on latch website. regards Dinesh Sharma Analyst secure meters limited ________________________________________ From: Xansys-temp [xansys-temp-bounces@xansystest.info] on behalf of Raghu Meesala [rmeesala@tervesinc.com] Sent: 14 January 2016 21:23 To: XANSYS Mailing List Temporary Home Subject: [Xansys] Help with LS-DYNA (Contact/Shear Problem) Hello: I am using ANSYS with LS-DYNA. Problem: I am trying to understand the forces applied on a solid ball (3.56" diameter) which is sheared through a hollow pipe (3.5" inch ID) Question: 1. How to import the ball into ANSYS so that I can place the ball at the starting point of the pipe and apply pressure. When I try to import the IGES I get it aligned to the center and I am unable to place where I would like to. 2. How can I select only the areas which I want to mesh, I want to select only the pipe areas after meshing to constraint the boundary conditions. Any literature or links for ANSYS LS-DYNA will be helpful. Thanks. Raghu Meesala Terves Inc. _______________________________________________ Xansys-temp mailing list Xansys-temp@xansystest.info http://xansystest.info/mailman/listinfo/xansys-temp_xansystest.info If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode. Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list This e-mail and any files transmitted with it are for the sole use of the intended recipient(s) and may contain confidential and privileged information. If you are not the intended recipient, please contact the sender and destroy all copies and the original message. Secure Meters Limited or its subsidiaries (Secure), are unable to exercise control or guarantee the integrity of/over the content contained in e-mails and any views expressed in this message are those of the individual unless expressly stated with due authority of Secure. If you have any problems with the emails from Secure contact: netadmin@securetogether.com _______________________________________________ Xansys-temp mailing list Xansys-temp@xansystest.info http://xansystest.info/mailman/listinfo/xansys-temp_xansystest.info If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode. Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list

PI

Prentice, Ian (GE Aviation, US)

Tue, Jan 19, 2016 12:32 PM

I think Dinesh is suffering from autocorrect.
Try searching for prepost on lstc website.

-----Original Message-----
From: Xansys-temp [mailto:xansys-temp-bounces@xansystest.info] On Behalf Of Raghu Meesala
Sent: Friday, January 15, 2016 9:51 AM
To: XANSYS Mailing List Temporary Home
Subject: Re: [Xansys] Help with LS-DYNA (Contact/Shear Problem)

Hey Dinesh:
I tried searching for latch but have not been lucky. Thank you for the thought.

Any other solutions please ?

Regards
Raghu Meesala
Terves Inc.

-----Original Message-----
From: Xansys-temp [mailto:xansys-temp-bounces@xansystest.info] On Behalf Of Dinesh Sharma-Mech
Sent: Thursday, January 14, 2016 10:19 PM
To: XANSYS Mailing List Temporary Home xansys-temp@xansystest.info
Subject: Re: [Xansys] Help with LS-DYNA (Contact/Shear Problem)

you can do these tasks in repost, which is free on latch website.
regards
Dinesh Sharma
Analyst
secure meters limited

From: Xansys-temp [xansys-temp-bounces@xansystest.info] on behalf of Raghu Meesala [rmeesala@tervesinc.com]
Sent: 14 January 2016 21:23
To: XANSYS Mailing List Temporary Home
Subject: [Xansys] Help with LS-DYNA (Contact/Shear Problem)

Hello:

I am using ANSYS with LS-DYNA.

Problem: I am trying to understand the forces applied on a solid ball (3.56" diameter) which is sheared through a hollow pipe (3.5" inch ID)
Question: 1. How to import the ball into ANSYS so that I can place the ball at the starting point of the pipe and apply pressure. When I try to import the IGES I get it aligned to the center and I am unable to place where I would like to.

How can I select only the areas which I want to mesh, I want to select only the pipe areas after meshing to constraint the boundary conditions.

Any literature or links for ANSYS LS-DYNA will be helpful. Thanks.

Raghu Meesala
Terves Inc.

Xansys-temp mailing list
Xansys-temp@xansystest.info
https://urldefense.proofpoint.com/v2/url?u=http-3A__xansystest.info_mailman_listinfo_xansys-2Dtemp-5Fxansystest.info&d=CwICAg&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=AkRDmyFKM-Gcbg2E4stpXLRMoaNeby_lUzZ4-N-V0FM&m=miCWDajBu0rEXunuVkKeyUBsjOgtlwRDqcakX-YdBFI&s=ZmMWOku4WY_bZ2muQDUG3BOF8crq8GAI2zT1lYoLazk&e=
If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode.

Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list This e-mail and any files transmitted with it are for the sole use of the intended recipient(s) and may contain confidential and privileged information. If you are not the intended recipient, please contact the sender and destroy all copies and the original message. Secure Meters Limited or its subsidiaries (Secure), are unable to exercise control or guarantee the integrity of/over the content contained in e-mails and any views expressed in this message are those of the individual unless expressly stated with due authority of Secure. If you have any problems with the emails from Secure contact: netadmin@securetogether.com

Xansys-temp mailing list
Xansys-temp@xansystest.info
https://urldefense.proofpoint.com/v2/url?u=http-3A__xansystest.info_mailman_listinfo_xansys-2Dtemp-5Fxansystest.info&d=CwICAg&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=AkRDmyFKM-Gcbg2E4stpXLRMoaNeby_lUzZ4-N-V0FM&m=miCWDajBu0rEXunuVkKeyUBsjOgtlwRDqcakX-YdBFI&s=ZmMWOku4WY_bZ2muQDUG3BOF8crq8GAI2zT1lYoLazk&e=
If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode.

Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list

Xansys-temp mailing list
Xansys-temp@xansystest.info
https://urldefense.proofpoint.com/v2/url?u=http-3A__xansystest.info_mailman_listinfo_xansys-2Dtemp-5Fxansystest.info&d=CwICAg&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=AkRDmyFKM-Gcbg2E4stpXLRMoaNeby_lUzZ4-N-V0FM&m=miCWDajBu0rEXunuVkKeyUBsjOgtlwRDqcakX-YdBFI&s=ZmMWOku4WY_bZ2muQDUG3BOF8crq8GAI2zT1lYoLazk&e=
If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode.

Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list

I think Dinesh is suffering from autocorrect. Try searching for prepost on lstc website. -----Original Message----- From: Xansys-temp [mailto:xansys-temp-bounces@xansystest.info] On Behalf Of Raghu Meesala Sent: Friday, January 15, 2016 9:51 AM To: XANSYS Mailing List Temporary Home Subject: Re: [Xansys] Help with LS-DYNA (Contact/Shear Problem) Hey Dinesh: I tried searching for latch but have not been lucky. Thank you for the thought. Any other solutions please ? Regards Raghu Meesala Terves Inc. -----Original Message----- From: Xansys-temp [mailto:xansys-temp-bounces@xansystest.info] On Behalf Of Dinesh Sharma-Mech Sent: Thursday, January 14, 2016 10:19 PM To: XANSYS Mailing List Temporary Home <xansys-temp@xansystest.info> Subject: Re: [Xansys] Help with LS-DYNA (Contact/Shear Problem) you can do these tasks in repost, which is free on latch website. regards Dinesh Sharma Analyst secure meters limited ________________________________________ From: Xansys-temp [xansys-temp-bounces@xansystest.info] on behalf of Raghu Meesala [rmeesala@tervesinc.com] Sent: 14 January 2016 21:23 To: XANSYS Mailing List Temporary Home Subject: [Xansys] Help with LS-DYNA (Contact/Shear Problem) Hello: I am using ANSYS with LS-DYNA. Problem: I am trying to understand the forces applied on a solid ball (3.56" diameter) which is sheared through a hollow pipe (3.5" inch ID) Question: 1. How to import the ball into ANSYS so that I can place the ball at the starting point of the pipe and apply pressure. When I try to import the IGES I get it aligned to the center and I am unable to place where I would like to. 2. How can I select only the areas which I want to mesh, I want to select only the pipe areas after meshing to constraint the boundary conditions. Any literature or links for ANSYS LS-DYNA will be helpful. Thanks. Raghu Meesala Terves Inc. _______________________________________________ Xansys-temp mailing list Xansys-temp@xansystest.info https://urldefense.proofpoint.com/v2/url?u=http-3A__xansystest.info_mailman_listinfo_xansys-2Dtemp-5Fxansystest.info&d=CwICAg&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=AkRDmyFKM-Gcbg2E4stpXLRMoaNeby_lUzZ4-N-V0FM&m=miCWDajBu0rEXunuVkKeyUBsjOgtlwRDqcakX-YdBFI&s=ZmMWOku4WY_bZ2muQDUG3BOF8crq8GAI2zT1lYoLazk&e= If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode. Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list This e-mail and any files transmitted with it are for the sole use of the intended recipient(s) and may contain confidential and privileged information. If you are not the intended recipient, please contact the sender and destroy all copies and the original message. Secure Meters Limited or its subsidiaries (Secure), are unable to exercise control or guarantee the integrity of/over the content contained in e-mails and any views expressed in this message are those of the individual unless expressly stated with due authority of Secure. If you have any problems with the emails from Secure contact: netadmin@securetogether.com _______________________________________________ Xansys-temp mailing list Xansys-temp@xansystest.info https://urldefense.proofpoint.com/v2/url?u=http-3A__xansystest.info_mailman_listinfo_xansys-2Dtemp-5Fxansystest.info&d=CwICAg&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=AkRDmyFKM-Gcbg2E4stpXLRMoaNeby_lUzZ4-N-V0FM&m=miCWDajBu0rEXunuVkKeyUBsjOgtlwRDqcakX-YdBFI&s=ZmMWOku4WY_bZ2muQDUG3BOF8crq8GAI2zT1lYoLazk&e= If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode. Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list _______________________________________________ Xansys-temp mailing list Xansys-temp@xansystest.info https://urldefense.proofpoint.com/v2/url?u=http-3A__xansystest.info_mailman_listinfo_xansys-2Dtemp-5Fxansystest.info&d=CwICAg&c=IV_clAzoPDE253xZdHuilRgztyh_RiV3wUrLrDQYWSI&r=AkRDmyFKM-Gcbg2E4stpXLRMoaNeby_lUzZ4-N-V0FM&m=miCWDajBu0rEXunuVkKeyUBsjOgtlwRDqcakX-YdBFI&s=ZmMWOku4WY_bZ2muQDUG3BOF8crq8GAI2zT1lYoLazk&e= If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode. Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list

xansys-temp@list.xansys.org

Help with LS-DYNA (Contact/Shear Problem)