Hi All, On my output file I get a block out output that starts with SUMMARY FOR CONTACT PAIRINDENTIFIED BY REAL CONSTANT SET 22 . . And then about 30 lines of potentially useful info, but most likely of no use. Does anyone know how to turn this off? Thanks in advance, Dan Bohlen Senior Engineer, Stress Analysis STAR review chairman, Cold Structures, Mounts GE Aircraft Engines 1 Neumann Way Evendale, OH 45215 USA Build B90 Col. H5 cube BK35-251 M/D H358 Cell 513-917-3402 Building 200 1st floor Col. Ma11 cube 1N026 3-4868 (no voicemail) "In God we trust, all others bring data." W Edwards Deming

I have not done contact simulations in a very long time. But maybe something similar to OUTPR could control your output file. ===================================== Mohammad A Gharaibeh, Ph.D. Associate Professor Department of Mechanical Engineering The Hashemite University P.O. Box 330127 Zarqa, 13133, Jordan Tel: +962 - 5 - 390 3333 Ext. 4771 Fax: +962 - 5 - 382 6348 ===================================== On Mon, 13 May 2024 at 8:31 PM Bohlen, Dan (GE Aerospace, US) via Xansys < xansys-temp@list.xansys.org> wrote: > Hi All, > > On my output file I get a block out output that starts with > > SUMMARY FOR CONTACT PAIRINDENTIFIED BY REAL CONSTANT SET 22 > . > . > And then about 30 lines of potentially useful info, but most likely of no > use. > > Does anyone know how to turn this off? > > Thanks in advance, > > > Dan Bohlen > Senior Engineer, Stress Analysis > STAR review chairman, Cold Structures, Mounts > GE Aircraft Engines > 1 Neumann Way > Evendale, OH 45215 USA > > Build B90 Col. H5 cube BK35-251 > M/D H358 Cell 513-917-3402 > > Building 200 1st floor > Col. Ma11 cube 1N026 3-4868 (no voicemail) > > "In God we trust, all others bring data." W Edwards Deming > > > > > > _______________________________________________ > Xansys mailing list -- xansys-temp@list.xansys.org > To unsubscribe send an email to xansys-temp-leave@list.xansys.org > If you are receiving too many emails from XANSYS please consider changing > account settings to Digest mode which will send a single email per day. > > Please send administrative requests such as deletion from XANSYS to > xansys-mod@tynecomp.co.uk and not to the list >

Normally, I would say /NOPR and /GOPR would be useful. However, that type of content you cited is right smack in the middle of the solver's buildout of the model. So I don't think there is any way to interject /NOPR at that exact point to stop the contact printout. It'd be analogous to putting a stop sign in the middle of the freeway; i.e., it's just not possible. I am kind of curious why this content is bothersome. Output files usually have hundreds/thousands of lines of useless content. But most analysts just ignore it and keep scrolling past. —Matt -----Original Message----- From: Mohammad Gharaibeh via Xansys <xansys-temp@list.xansys.org> Sent: May 13, 2024 2:45 PM To: XANSYS Mailing List Home <xansys-temp@list.xansys.org> Cc: Mohammad Gharaibeh <mgharai1@binghamton.edu> Subject: [Xansys] Re: [External Email] Surface to surface output V19.2 classic I have not done contact simulations in a very long time. But maybe something similar to OUTPR could control your output file. ===================================== Mohammad A Gharaibeh, Ph.D. Associate Professor Department of Mechanical Engineering The Hashemite University P.O. Box 330127 Zarqa, 13133, Jordan Tel: +962 - 5 - 390 3333 Ext. 4771 Fax: +962 - 5 - 382 6348 ===================================== On Mon, 13 May 2024 at 8:31 PM Bohlen, Dan (GE Aerospace, US) via Xansys < xansys-temp@list.xansys.org> wrote: > Hi All, > > On my output file I get a block out output that starts with > > SUMMARY FOR CONTACT PAIRINDENTIFIED BY REAL CONSTANT SET 22 . > . > And then about 30 lines of potentially useful info, but most likely of > no use. > > Does anyone know how to turn this off? > > Thanks in advance, > > > Dan Bohlen > Senior Engineer, Stress Analysis > STAR review chairman, Cold Structures, Mounts GE Aircraft Engines > 1 Neumann Way > Evendale, OH 45215 USA > > Build B90 Col. H5 cube BK35-251 > M/D H358 Cell 513-917-3402 > > Building 200 1st floor > Col. Ma11 cube 1N026 3-4868 (no voicemail) > > "In God we trust, all others bring data." W Edwards Deming > > > > > > _______________________________________________ > Xansys mailing list -- xansys-temp@list.xansys.org To unsubscribe send > an email to xansys-temp-leave@list.xansys.org If you are receiving too > many emails from XANSYS please consider changing account settings to > Digest mode which will send a single email per day. > > Please send administrative requests such as deletion from XANSYS to > xansys-mod@tynecomp.co.uk and not to the list > _______________________________________________ Xansys mailing list -- xansys-temp@list.xansys.org To unsubscribe send an email to xansys-temp-leave@list.xansys.org If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode which will send a single email per day. Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list

Turns out the cntr,3 is the offending command Dan Bohlen Senior Engineer, Stress Analysis STAR review chairman, Cold Structures, Mounts GE Aircraft Engines 1 Neumann Way Evendale, OH  45215   USA Build B90 Col. H5   cube BK35-251  M/D H358   Cell  513-917-3402 Building 200 1st floor Col. Ma11  cube 1N026  3-4868 (no voicemail) "In God we trust, all others bring data." W Edwards Deming -----Original Message----- From: Bohlen, Dan (GE Aerospace, US) via Xansys <xansys-temp@list.xansys.org> Sent: Monday, May 13, 2024 1:30 PM To: XANSYS Mailing List Home <xansys-temp@list.xansys.org> Cc: Bohlen, Dan (GE Aerospace, US) <dan.bohlen@ge.com> Subject: EXT: [Xansys] Surface to surface output V19.2 classic WARNING: This email originated from outside of GE. Please validate the sender's email address before clicking on links or attachments as they may not be safe. Hi All, On my output file I get a block out output that starts with SUMMARY FOR CONTACT PAIRINDENTIFIED BY REAL CONSTANT SET 22 . . And then about 30 lines of potentially useful info, but most likely of no use. Does anyone know how to turn this off? Thanks in advance, Dan Bohlen Senior Engineer, Stress Analysis STAR review chairman, Cold Structures, Mounts GE Aircraft Engines 1 Neumann Way Evendale, OH 45215 USA Build B90 Col. H5 cube BK35-251 M/D H358 Cell 513-917-3402 Building 200 1st floor Col. Ma11 cube 1N026 3-4868 (no voicemail) "In God we trust, all others bring data." W Edwards Deming _______________________________________________ Xansys mailing list -- xansys-temp@list.xansys.org To unsubscribe send an email to xansys-temp-leave@list.xansys.org If you are receiving too many emails from XANSYS please consider changing account settings to Digest mode which will send a single email per day. Please send administrative requests such as deletion from XANSYS to xansys-mod@tynecomp.co.uk and not to the list